OH HV 2018 IMC Update Part 1

4 Hour Course
4.6 27 Reviews
$49.00

Course Description
Course Outline

After completing this course, the licensee will understand some of the key life safety requirements for mechanical systems.

Course ID(s): 4921911
Approved By: Ohio Construction Industry Licensing Board (OCILB)

Add to Cart (877) 724-6150

2018 IMC Update Part 1
- Checkpoint 1
- 2018 IMC Update - Segment 1 [6 Activities]
  - 01. Effective Use of the International Mechanical Code
  - 02. Scope, Application, Intent and Severability - IMC Section 101
  - 03. Existing Installations, Maintenance, Additions, Alterations, and Repairs - IMC Sections 102.1, 102.2, 102.3, 102.5
  - 04. Changes in Occupancy and Historic Buildings - IMC Sections 102.5-102.7
  - 05. Temporary Equipment, Systems and Uses - IMC Section 110
  - 06. General Definitions of Key Terms - IMC Section 202
- Checkpoint 2
- 2018 IMC Update - Segment 2 [6 Activities]
  - 01. General Regulations, Third Party Certification, and Listing and Labeling IMC Sections 301, 301.2, 301.3, 301.5, and 301.7
  - 02. Protection of Structures - IMC Section 302
  - 03. Equipment and Appliance Location - IMC Section 303
  - 04. Installation - IMC Section 304
  - 05. Access and Service Space - IMC Section 306
  - 06. Condensate Disposal - IMC Section 307
- Checkpoint 3
- 2018 IMC Update - Segment 3 [6 Activities]
  - 01. General Requirements for Ventilation, Natural and Mechanical Ventilation - IMC Sections 401, 402, 403, and 404
  - 02. Zone Outdoor Airflow and Breathing Zone Outdoor Airflow - IMC Section 403
  - 03. General Exhaust Requirements - IMC Section 501
  - 04. Required Exhaust Systems - IMC Section 502
  - 05. Application of Flammable Finishes - IMC Section 502.7
  - 06. Hazardous Materials, General Requirements - IMC Section 502.8
- Checkpoint 4
- 2018 IMC Update - Segment 4 [6 Activities]
  - 01. Flammable and Combustible Liquids - IMC Section 502.9.5
  - 02. Highly Toxic Liquids and Toxic Compressed Gases - IMC Section 502.9.6,502.9.7, 502.9.8
  - 03. Hazardous Production Materials - IMC Section 502.10
  - 04. Repair Garages including Motor Vehicle Operation - IMC Sections 502.14-502.16
  - 05. Manicure and Pedicure Stations - IMC Section 502.20
  - 06. Clothes Dryer Exhaust - IMC Section 504
- Checkpoint 5
- 2018 IMC Update - Segment 5 [7 Activities]
  - 01. Specific Requirements for Domestic and Commercial Clothes Dryer Ducts - IMC Section 504.8
  - 02. Domestic Cooking Exhaust Equipment - IMC Section 505
  - 03. Commercial Kitchen Hood Ventilation System Ducts and Exhaust Equipment - IMC Section 506
  - 04. Specific Code Requirements for Grease Ducts IMC Sections 506.3.3 506.3.12
  - 05. Exhaust outlets Serving Type 1 Hoods - IMC Section 506.3.13
  - 06. Ducts Serving Type 2 Hoods - IMC Section 506.4
  - 07. Pollution Control Units and Exhaust Equipment - IMC Section 506.5
- Checkpoint 6
- 2018 IMC Update - Segment 6 [7 Activities]
  - 01. Commercial Kitchen Hoods - IMC Section 507
  - 02. Type 2 Hoods - IMC Section 507.3
  - 03. Hood Size, Location, and Capacity - IMC Section 507.4
  - 04. Performance Test - IMC Section 507.6
  - 05. Commercial Kitchen Make-up Air and Fire Suppression - IMC Section 508
  - 06. Hazardous Exhaust, Design and Operation - IMC Section 510
  - 07. Minimum Duct Thicknesses for Hazardous Exhaust - IMC Section 510.9
- Checkpoint 7
- 2018 IMC Update - Segment 7 [6 Activities]
  - 01. Dust, Stock, and Refuse Conveying Systems - IMC Section 511
  - 02. Sub-slab Soil Exhaust Systems - IMC Section 512
  - 03. Smoke Control Systems - IMC Section 513
  - 04. Smoke Barrier Construction - IMC Section 513.5
  - 05. Smoke Control Methods - IMC Section 513.6
  - 06. Equipment for Smoke Control Systems - IMC Section 513.10
- Checkpoint 8
- 2018 IMC Update - Segment 8 [6 Activities]
  - 01. Detection and Control Systems - IMC Section 513.12
  - 02. Energy Recovery Ventilation Systems - IMC Section 514
  - 03. Maintenance of the International Mechanical Code
  - 04. Modifications and Alternate Methods
  - 05. Alternate Means and Methods
  - 06. Unsafe Mechanical Systems
Course Completion
- Mandatory Questionnaire
- Certificate of Completion

Instructor Bio

Reggie Hucks is an Inspection Services Administrator for High Point, NC. He has also served as the Code Administrator for Brunswick County and is a Level 3 Mechanical, Building, and Plumbing Inspector. He also is a certified mechanical contractor in North Carolina.

Course Reviews

4.6

27 Reviews

Add to Cart

OH HV 2018 IMC Update Part 1

Course Description

Course Outline

Instructor Bio

Course Reviews