This Installation Checklists (2023 NEC) course covers updated 2023 NEC installation methods that inspectors check for in commercial or residential inspections. During the four-hour Department of Consumer and Business Services-approved course, Oregon electricians will learn about 2023 NEC methods for installing wiring above the ceiling, underground, and on rooftops.
Also included are code checklists that cover the following:
- What’s needed to pass rough inspections
- Final inspection requirements
- Installing and grounding panelboards, services, and transformers
Learning Objectives:
Electricians in New Mexico who take this course will:
- Know the updated 2023 NEC requirements electrical inspectors look for on jobsites
- Be prepared to confidently respond to electrical inspector requirements during different phases of a project
- Understand 2023 NEC requirements when installing electrical systems and be better prepared to pass underground, above ceiling, rooftop, service, panelboard, transformer, and rough and final electrical inspections
To receive credit for the course, students must complete a total of 50 multiple-choice questions with a score of at least 70%. Additionally, students must spend at least 200 active minutes within the course (50-minute credit hours) to receive credit.
Course ID(s): 28505283
Approved By: Department of Consumer & Business Services - Building Codes Division
- Installation Checklists (2023 NEC)
- Installation Checklists (2023 NEC) [50 Activities]
- 01. Underground - 300.5(F) Backfill
- 02. Underground - 300.5(H) Bushings
- 03. Underground - 300.5(J) Earth Movement
- 04. Underground - Table 300.5(A) Minimum Cover Distance
- 05. Underground - 300.5(G) Raceway Seals
- 06. Underground - 314.27(B) Floor Boxes
- 07. Underground - 250.52(A)(3) Concrete-Encased Electrode
- 08. Rough Inspection - Rough Inspection Basics
- Additional Activities
- 09. Rough Inspection - 517.13(A) Branch Circuits Serving Patient Care Areas
- 10. Rough Inspection - 110.12(A) Unused Openings
- 11. Rough Inspection - 330.30 MC Cable; Securing and Supporting
- 12. Rough Inspection - 342.14, 344.14, and 358.14 Dissimilar Metals
- 13. Rough Inspection - Article 100 Definitions: Accessible
- 14. Rough Inspection - 300.4(A)(1) Cables and Raceways Through Wood Members; Bored Holes
- 15. Above the Ceiling - 300.11(A)&(B) Secured In Place
- 16. Above the Ceiling - 200.4(B) Multiple Circuits
- 17. Above the Ceiling - 424.66/110.26(A)(4) Duct Heaters with Limited Access Above Ceiling/Working Space; Limited Access
- 18. Above the Ceiling - 410.110(A) Special Provisions for Flush and Recessed Luminaires; Clearance from Combustible Material
- 19. Above the Ceiling - 590.3(D) Removal of Temporary Wiring
- 20. Above the Ceiling - 300.22(C) Other Spaces Used for Environmental Air
- 21. Above the Ceiling - 250.104(A)(B)(C) Bonding of Piping and Exposed Structural Steel
- 22. Above the Ceiling - 410.117(C) Luminaires; Tap Conductors
- 23. Above the Ceiling - 300.21 Spread of Fire or Products of Combustion
- 24. Rooftop - 250.110 Equipment Fastened in Place or Connected by Permanent Wiring Methods
- 25. Rooftop - 250.12 Clean Surfaces
- 26. Rooftop - 110.22(A) Identification of Disconnecting Means
- 27. Rooftop - 250.97 Bonding for Over 250 Volts
- 28. Rooftop - 440.4(B) Marking on HVAC Equipment
- 29. Rooftop - 314.23(E)&(F) Raceway Supported Enclosures
- 30. Rooftop - 210.63(A) Heating, Air-Conditioning, and Refrigeration Equipment Outlet
- 31. Service, Panelboards, Transformers - 110.24 Available Fault Current
- 32. Service, Panelboards, Transformers - 200.6 Identification of Grounded Conductors
- 33. Service, Panelboards, Transformers - 250.119 Identification of Equipment Grounding Conductors
- 34. Service, Panelboards, Transformers - 210.5(C)(1) & 235.5(C)(1) Identification of Ungrounded Conductors
- 35. Service, Panelboards, Transformers - 110.26(A)(1) Working Space
- 36. Service, Panelboards, Transformers - 408.5 Clearance for Conductor Entering Bus Enclosures
- 37. Service, Panelboards, Transformers - 250.30(A)(1) System Bonding Jumpers
- 38. Service, Panelboards, Transformers - 250.30(A)(4&5) Grounding Electrode and Grounding Electrode Conductor, Single Separately Derived System
- 39. Final Inspection - 450.10(A) Grounding of Dry-Type Transformer Enclosures
- 40. Final Inspection - 700.12 General Requirements
- 41. Final Inspection - 700.16 Emergency Illumination, Part 1
- 42. Final Inspection - 700.16 Emergency Illumination, Part 2
- 43. Final Inspection - 110.3(B) Installation and Use
- 44. Final Inspection - 427.22 Pipelines and Vessels; Ground-Fault Protection of Equipment
- 45. Final Inspection - Final Equipment Installation
- 46. Final Inspection - 700.12(H)(2)(3) Battery-Equipped Emergency Luminaires
- 47. Final Inspection - 700.11 Identification of Emergency Lighting Circuits
- 48. Final Inspection - 210.8 GFCI Protection for Personnel
- 49. Final Inspection - 110.25 Lockable Disconnecting Means
- 50. Final Inspection - 408.4(A) Circuit Directory
- Installation Checklists (2023 NEC) [50 Activities]
- Course Completion
- Mandatory Questionnaire
- Certificate of Completion
- Expedited Reporting Available
