This course explains updated installation methods based on the 2023 NEC that electricians must use to pass both rough and final jobsite inspections.
The course material, which is approved by the Division of Professional Licensing, covers updated code requirements for installing wiring underground, above ceilings, and on rooftops.
Also included are 2023 NEC checklists that go over:
- Required steps to pass rough electrical inspections
- Required steps to pass final electrical inspections
- Installing and grounding panelboards, services, and transformers
Learning Objectives:
Electricians in Utah who complete this course will:
- Know how to use 2023 NEC installation methods for electrical systems to pass rough and final electrical inspections, including underground, above ceiling, and rooftop wiring
- Understand the installation codes electrical inspectors look for on jobsites
- Know how to respond to inspector requirements during different phases of an installation project
- Know how to properly install and ground services, panelboards, and transformers
Each section within the course ends with a multiple-choice review question. To pass the course, students must answer all 50 questions with a total score of at least 70%. Additionally, students will only receive credit once they spend 200 active minutes in the course (50-minute credit hours).
Course ID(s): 23275
Approved By: Division of Occupational and Professional Licensing - Electrical
- Installation Checklists (2023 NEC)
- Installation Checklists (2023 NEC) [50 Activities]
- 01. Underground - 300.5(F) Backfill
- 02. Underground - 300.5(H) Bushings
- 03. Underground - 300.5(J) Earth Movement
- 04. Underground - Table 300.5(A) Minimum Cover Distance
- 05. Underground - 300.5(G) Raceway Seals
- 06. Underground - 314.27(B) Floor Boxes
- 07. Underground - 250.52(A)(3) Concrete-Encased Electrode
- 08. Rough Inspection - Rough Inspection Basics
- Additional Activities
- 09. Rough Inspection - 517.13(A) Branch Circuits Serving Patient Care Areas
- 10. Rough Inspection - 110.12(A) Unused Openings
- 11. Rough Inspection - 330.30 MC Cable; Securing and Supporting
- 12. Rough Inspection - 342.14, 344.14, and 358.14 Dissimilar Metals
- 13. Rough Inspection - Article 100 Definitions: Accessible
- 14. Rough Inspection - 300.4(A)(1) Cables and Raceways Through Wood Members; Bored Holes
- 15. Above the Ceiling - 300.11(A)&(B) Secured In Place
- 16. Above the Ceiling - 200.4(B) Multiple Circuits
- 17. Above the Ceiling - 424.66/110.26(A)(4) Duct Heaters with Limited Access Above Ceiling/Working Space; Limited Access
- 18. Above the Ceiling - 410.110(A) Special Provisions for Flush and Recessed Luminaires; Clearance from Combustible Material
- 19. Above the Ceiling - 590.3(D) Removal of Temporary Wiring
- 20. Above the Ceiling - 300.22(C) Other Spaces Used for Environmental Air
- 21. Above the Ceiling - 250.104(A)(B)(C) Bonding of Piping and Exposed Structural Steel
- 22. Above the Ceiling - 410.117(C) Luminaires; Tap Conductors
- 23. Above the Ceiling - 300.21 Spread of Fire or Products of Combustion
- 24. Rooftop - 250.110 Equipment Fastened in Place or Connected by Permanent Wiring Methods
- 25. Rooftop - 250.12 Clean Surfaces
- 26. Rooftop - 110.22(A) Identification of Disconnecting Means
- 27. Rooftop - 250.97 Bonding for Over 250 Volts
- 28. Rooftop - 440.4(B) Marking on HVAC Equipment
- 29. Rooftop - 314.23(E)&(F) Raceway Supported Enclosures
- 30. Rooftop - 210.63(A) Heating, Air-Conditioning, and Refrigeration Equipment Outlet
- 31. Service, Panelboards, Transformers - 110.24 Available Fault Current
- 32. Service, Panelboards, Transformers - 200.6 Identification of Grounded Conductors
- 33. Service, Panelboards, Transformers - 250.119 Identification of Equipment Grounding Conductors
- 34. Service, Panelboards, Transformers - 210.5(C)(1) & 235.5(C)(1) Identification of Ungrounded Conductors
- 35. Service, Panelboards, Transformers - 110.26(A)(1) Working Space
- 36. Service, Panelboards, Transformers - 408.5 Clearance for Conductor Entering Bus Enclosures
- 37. Service, Panelboards, Transformers - 250.30(A)(1) System Bonding Jumpers
- 38. Service, Panelboards, Transformers - 250.30(A)(4&5) Grounding Electrode and Grounding Electrode Conductor, Single Separately Derived System
- 39. Final Inspection - 450.10(A) Grounding of Dry-Type Transformer Enclosures
- 40. Final Inspection - 700.12 General Requirements
- 41. Final Inspection - 700.16 Emergency Illumination, Part 1
- 42. Final Inspection - 700.16 Emergency Illumination, Part 2
- 43. Final Inspection - 110.3(B) Installation and Use
- 44. Final Inspection - 427.22 Pipelines and Vessels; Ground-Fault Protection of Equipment
- 45. Final Inspection - Final Equipment Installation
- 46. Final Inspection - 700.12(H)(2)(3) Battery-Equipped Emergency Luminaires
- 47. Final Inspection - 700.11 Identification of Emergency Lighting Circuits
- 48. Final Inspection - 210.8 GFCI Protection for Personnel
- 49. Final Inspection - 110.25 Lockable Disconnecting Means
- 50. Final Inspection - 408.4(A) Circuit Directory
- Installation Checklists (2023 NEC) [50 Activities]
- Course Completion
- Mandatory Questionnaire
- Certificate of Completion
- Guaranteed Next Business Day Reporting
