FL 2018 IMC Update

8 Hour Course

$95.00

Course Description
Course Outline

This Florida-approved course will review and highlight essential code requirements of chapters 1 through 12 in the 2018 International Mechanical Code.

After completing this course, the licensee will understand some of the key life safety requirements for mechanical systems. Changes from the previous version of the IMC will be highlighted in the commentary where appropriate.

Course ID(s): 0614432
Approved By: Florida DBPR

Add to Cart (877) 724-6150

2018 IMC Update
- 2018 IMC Update Part 1 [50 Activities]
  - 01. Effective Use of the International Mechanical Code
  - 02. Scope, Application, Intent and Severability - IMC Section 101
  - 03. Existing Installations, Maintenance, Additions, Alterations, and Repairs - IMC Sections 102.1, 102.2, 102.3, 102.5
  - 04. Changes in Occupancy and Historic Buildings - IMC Sections 102.5-102.7
  - 05. Temporary Equipment, Systems and Uses - IMC Section 110
  - 06. General Definitions of Key Terms - IMC Section 202
  - 07. General Regulations, Third Party Certification, and Listing and Labeling IMC Sections 301, 301.2, 301.3, 301.5, and 301.7
  - 08. Protection of Structures - IMC Section 302
  - View Additional Activities
    - 09. Equipment and Appliance Location - IMC Section 303
    - 10. Installation - IMC Section 304
    - 11. Access and Service Space - IMC Section 306
    - 12. Condensate Disposal - IMC Section 307
    - 13. General Requirements for Ventilation, Natural and Mechanical Ventilation - IMC Sections 401, 402, 403, and 404
    - 14. Zone Outdoor Airflow and Breathing Zone Outdoor Airflow - IMC Section 403
    - 15. General Exhaust Requirements - IMC Section 501
    - 16. Required Exhaust Systems - IMC Section 502
    - 17. Application of Flammable Finishes - IMC Section 502.7
    - 18. Hazardous Materials, General Requirements - IMC Section 502.8
    - 19. Flammable and Combustible Liquids - IMC Section 502.9.5
    - 20. Highly Toxic Liquids and Toxic Compressed Gases - IMC Section 502.9.6,502.9.7, 502.9.8
    - 21. Hazardous Production Materials - IMC Section 502.10
    - 22. Repair Garages including Motor Vehicle Operation - IMC Sections 502.14-502.16
    - 23. Manicure and Pedicure Stations - IMC Section 502.20
    - 24. Clothes Dryer Exhaust - IMC Section 504
    - 25. Specific Requirements for Domestic and Commercial Clothes Dryer Ducts - IMC Section 504.8
    - 26. Domestic Cooking Exhaust Equipment - IMC Section 505
    - 27. Commercial Kitchen Hood Ventilation System Ducts and Exhaust Equipment - IMC Section 506
    - 28. Specific Code Requirements for Grease Ducts IMC Sections 506.3.3 506.3.12
    - 29. Exhaust outlets Serving Type 1 Hoods - IMC Section 506.3.13
    - 30. Ducts Serving Type 2 Hoods - IMC Section 506.4
    - 31. Pollution Control Units and Exhaust Equipment - IMC Section 506.5
    - 32. Commercial Kitchen Hoods - IMC Section 507
    - 33. Type 2 Hoods - IMC Section 507.3
    - 34. Hood Size, Location, and Capacity - IMC Section 507.4
    - 35. Performance Test - IMC Section 507.6
    - 36. Commercial Kitchen Make-up Air and Fire Suppression - IMC Section 508
    - 37. Hazardous Exhaust, Design and Operation - IMC Section 510
    - 38. Minimum Duct Thicknesses for Hazardous Exhaust - IMC Section 510.9
    - 39. Dust, Stock, and Refuse Conveying Systems - IMC Section 511
    - 40. Sub-slab Soil Exhaust Systems - IMC Section 512
    - 41. Smoke Control Systems - IMC Section 513
    - 42. Smoke Barrier Construction - IMC Section 513.5
    - 43. Smoke Control Methods - IMC Section 513.6
    - 44. Equipment for Smoke Control Systems - IMC Section 513.10
    - 45. Detection and Control Systems - IMC Section 513.12
    - 46. Energy Recovery Ventilation Systems - IMC Section 514
    - 47. Maintenance of the International Mechanical Code
    - 48. Modifications and Alternate Methods
    - 49. Alternate Means and Methods
    - 50. Unsafe Mechanical Systems
- 2018 IMC Update Part 2 [50 Activities]
  - 01. General Requirements for Ducts Systems - IMC Section 601
  - 02. Plenums IMC Section 602
  - 03. Duct Construction and Installation - IMC Section 603
  - 04. Insulation and Air Filters IMC Sections 604 and 605
  - 05. Smoke Detection Systems Control IMC Section 606
  - 06. Duct and Transfer Openings - IMC Section 607
  - 07. Combustion Air and Ventilation - IMC Section 701
  - 08. Chimney and Vents General Requirements - IMC Section 801
  - View Additional Activities
    - 09. Vents and Connectors Specific Requirements - IMC Section 802 and 803
    - 10. Direct Vent, Integral Vent, and Mechanical Draft Systems - IMC Section 804
    - 11. Factory Built and Metal Chimneys - IMC Sections 805 and 806
    - 12. General Requirements for Specific Appliances - IMC Sections 901, 902, and 903
    - 13. Pellet Fuel Burning Appliances, Fireplace Stoves, and Room Heaters - IMC Sections 904 and 905
    - 14. Cooling Towers, Evaporative Coolers, and Fluid Coolers - IMC Section 908 and 928
    - 15. Vented Wall Furnaces, Floor Furnaces, Duct Furnaces, Infrared Radiant and Infrared Heaters - IMC Sections 909-912
    - 16. Clothes Dryers, Sauna Heaters, and High Volume Large Diameter Fans - IMC Sections 913, 914, and 929
    - 17. Forced Air Warm Furnaces and Radiant Heating Systems - IMC Sections 918 and 927
    - 18. General Requirements for Boilers, Water Heaters, and Pressure Vessels - IMC Section 1001
    - 19. Boilers - IMC Section 1004
    - 20. Safety Devices for Boilers, Water Heaters and Pressure Vessels - IMC Sections 1005, 1006, 1007, and 1008
    - 21. Expansion Tanks, Gauges and Tests - IMC Sections 1009, 1010, 1011
    - 22. General requirements for Refrigeration - IMC Section 1101
    - 23. Technical System Requirements - IMC Section 1102
    - 24. Refrigeration System Classification - IMC Section 1103
    - 25. Refrigerant System Classifications (Continued) - IMC Section 1103
    - 26. Building Occupancy Classifications - IMC Section 1103.2
    - 27. System Application Requirements - IMC Section 1104
    - 28. Refrigerant Restrictions - IMC Section 1104.3
    - 29. Machinery Room General Requirements - IMC Section 1105
    - 30. Machinery Rooms Special Requirements - IMC Section 1106
    - 31. Refrigerant Piping - IMC Section 1107
    - 32. Materials for Refrigerant Piping and Tubing - IMC Section 1107.5
    - 33. Piping Joints and Refrigerant Parts - IMC Section 1107.6
    - 34. Field Tests of Refrigerant Systems and Periodic Testing - IMC Sections 1108 and 1109
    - 35. General Requirements for Hydronic Piping - IMC Section 1201 and 1202
    - 36. Hydronic Piping Joints and Connections IMC Section 1203
    - 37. Piping Insulation and Valves - IMC Sections 1204 and 1205
    - 38. Piping Installation - IMC Section 1206
    - 39. Embedded Piping - IMC Section 1209
    - 40. Plastic Pipe Ground Source Loop Systems - IMC Section 1210
    - 41. General Requirements for Fuel Oil Piping and Storage - IMC Section 1301
    - 42. Fuel Oil Piping Joints and Connections - IMC Section 1303
    - 43. Fuel Oil Piping System Installations - IMC Section 1305
    - 44. Fuel Oil Gauging, Valves, and Testing - IMC Sections 1306, 1307, and 1308
    - 45. General Requirements for Solar Thermal Systems - IMC Sections 1401 and 1402
    - 46. Solar Installations and Heat Transfer Fluids - IMC Sections 1402 and 1403
    - 47. Chimney Connector Pass-through Examples - IMC Appendix A
    - 48. How Industry Works to Create Codes and Standards
    - 49. Agencies Responsible for Specific Standards Found in the IMC
    - 50. Permits Why are they Necessary?
Course Completion
- Mandatory Questionnaire
- Certificate of Completion
- Expedited Reporting Available for $19

Instructor Bio

Reggie Hucks is an Inspection Services Administrator for High Point, NC. He has also served as the Code Administrator for Brunswick County and is a Level 3 Mechanical, Building, and Plumbing Inspector. He also is a certified mechanical contractor in North Carolina.

Add to Cart

FL 2018 IMC Update

Course Description

Course Outline

Instructor Bio